Hornby R8008 00 Gauge Ponte Grande Suspension

Brand:

3.6/5;

69.06

calibro OO Dimensioni Altezza 1.372 millimetri di lunghezza (un livello all'altro) 80 millimetri Non DCC pronto Livrea configuración de rueda

calibro OO Dimensioni Altezza 1.372 millimetri di lunghezza (un livello all'altro) 80 millimetri Non DCC pronto Livrea configuración de rueda
Assemblaggio necessario ‎No
Batterie/Pile incluse? ‎No
Batterie/Pile necessarie? ‎No
Colore ‎Marrone
Dimensioni prodotto ‎36,2 x 12 x 20 cm; 350 grammi
Distanza binari ‎OO
Età consigliata dal produttore ‎14 anni e più
Lingua: ‎Inglese
Numero modello ‎R8008
Numero modello articolo ‎R8008
Peso articolo ‎350 g
Scala ‎1:76
Telecomando incluso? ‎No
Tipi di materiale ‎Mattone

3.6

6 Review
5 Star
79
4 Star
11
3 Star
3
2 Star
4
1 Star
3

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con*

Scritto da: Castrum1348
Buon rapporto tra qualità dell'oggetto e il suo prezzo Amazon
Superfluo rispondere alla domanda sull'utilizzazione, vista la natura dell'oggetto acquistato. L'oggetto - un modello in scala - è di buona fattura e di agevole montaggio e depone bene per la sua casa produttrice. Smentisce, almeno una volta, il cospicuo aumento di prezzo riscontrabile su Amazon se confrontato, relativamente al settore modellismo, con i prezzi delle ditte produttrici o con quello di altri canali di acquisto on-line.
Scritto da: eric thuillier
Très joli bâtiment en plastique à monter.
Vraiment très bien, prends un peu plus de place que prévu. Je fais des réseaux ferroviaires éphémère, j'espère pouvoir le ranger, démonter sans l'abîmer.
Scritto da: Roy Webb
It is certainly "Grand"
This superbly modelled suspension bridge would be an asset to most layouts, but you need lots of space to use it as a working rail bridge. Assembled it is 1370mm long, and then you need to add the space to achieve a slow incline at both ends, which probably would take you up to 8ft.at least.even using curves.In my case my layout size is only 6,x4-6" so I cannot use it in the intended way at present.I decided to use it as a road bridge, and parked some vehicles on it, and put it across my layout, it just fits. I recognise that this would not be to everyones satisfaction, but it suits my layout fine, and has greatly enhanced it and becomes very much a centre piece.To put it across the rails in this way you may need to know where the towers fall, so I offer the appended measurements.The distance between the end towers, and the large tower is approx. 300mm,and the distance between the two large towers is approx. 625mm. Just as a matter of interest the height to the top of the main towers is 200mm The kit is easy to assemble, and clicks together well. The most tricky part is hanging the suspension units which are fitted on little C hooks on small pegs, these can be in the habit of 'springing' if you move the bridge, so I used a little drop of clear plastic glue on each peg, and this is not noticeable. I think this is good value for money off Amazon.
Scritto da: Amazon Kunde
Top Artikel
Sehr schöne Brücke
Scritto da: Ken Chapman
Not recommended for a smaller layout
Not for a small layout by any means, but certainly can be a showcase bridge if included in a larger layout. Great for the river valley or even just to get the mainline over those rail yards. Probably best if used on a multi-level layout as, as a previous reviewer noted, the distance to create a grade to raise and lower the track to the bridge height eats up a lot of layout space. Certainly a good purchase for the right situation.
Scritto da: LOTHARD
produit interessant
comment relier 2 circuits de train par un passage mobile le pont hornby y répond, bien sure il faut le fixer sur une planche mobile il n'est qu'à simple voie et commence à accuser son age mais pas d'équivalence à ce prix

Prodotti correlati

Scopri il nostro network internazionale

Spediamo in 28 paesi, oltre 200.000 prodotti. Resta aggiornato, iscriviti alla newsletter.

Array